- Detta ämne har 3 svar, 2 deltagare, och uppdaterades senast för 5 år, 5 månader sedan av
.
-
Ämne
-
Hi everybody,
My name is Cezar and I am a hamradio operator from Bucharest, Romania (KN34AK, call is YO3FHM). I finally managed to receive the SAQ transmission today, starting with 08:45 UTC on 17.2 kHz VLF. I also received the 2nd transmission, starting with 10:45 UTC.
The receiving conditions were very poor, with a lot of noise coming from switching power supplies of the industrial telecommunication equipments that works in the immediate vicinity of my radio shack. To receive the SAQ signal, I was forced to use both the transceiver’s noise filters and band narrowing up to 200Hz. In these conditions, the signal report was about 459.
I used an Icom IC-7300 transceiver, a miniWhip antenna and a passive VLF converter.
The converter consist in a simple SBL-1 integrated mixer with 7dBm 5MHz carrier signal applied from a HP RF generator, an elliptic low-pass filter applied between the miniWhip antenna and the input of the SBL-1 mixer (for this time I used the IF input instead the RF input, to avoid the input transformer that cannot work properly on such low frequencies). I used the RF port of the SBL-1 as 50 ohms output device to the IC-7300.
It is my first attempt to receive SAQ and I am very happy to see that I did it 🙂
My congratulations for the entire team from SAQ !Best regards,
Cezar YO3FHM
-
-
Good morning!
1 year from my first attempt to receive the SAQ transmission (see above).
For this time, I tried in an open field from the west side of my city (Bucharest), using a ferrite antenna, an active converter with SA612 and my IC-7300 transceiver.
The ferrite antenna has an inductance of 18 mH and is tuned on 17.2 KHz with a fixed 4.7nF capacitor and a variable one (15-550 pF). The converter is the typical schematic from the NE612 application note, but I put in the front of it an RF cascode preamp (FET+BJT) – around 20dB @12V. The carrier crystal is 10.7 MHz.
Here is the preamp schematic and LTSpice simulations results:
The 4uH coil is made only for test & measuring reasons (is a matching to 50 ohm port of my test equipment); after the alignment, I simply removed it.
And this is my open field setup (cclick to enlarge) :
This is a clip from the first transmission (9 UTC):
The frequency is 10717.25 ; it has a small 50Hz lift, but I didn’t tried to readjust.
I have a todo list for some improvements of the VLF converter, I will return to publish the project when will be ready.Best regards,
Cezar YO3FHM -
@Bernd: Congratulations for your receiver, Bernd! Works nice, and I suppose that in that “green” field you are far away from electric and EM interferences. Good job!
In my location, I have many problems with switching power supplies, different inverters, etc.
Look here how bad was the local VLF spectrum in the morning, at the 1st SAQ transmission:
I put a digital edited MP3 with the content of the 1st SAQ transmission here .
Fortunately, I had slightly good conditions at the 3rd SAQ transmission:
and screenshot #2:
For this session, I didn’t make any digital edit.I also tried to receive with the miniWhip connected to the soundcard, using Spectrum Lab.
Look at the images below (click on them to enlarge):
The captured audio from the soundcard session is here:
Record #1
Record #2I know that is not much, but considering the perturbations around, I am OK with what I done today.
Hope that the next time will be better !Regards from Bucharest,
Cezar YO3FHM -
-
